Parameter Function (SSExplanationDefault/ExampleDCP 2G & 3G UK CUSTOMERSDCP 4G UK CUSTOMERS
Device access, identification and status functions






000Operator block status - locked/unlocked

Pin code used to enter configuration mode in handset or serial*#*1234*#*2D DCP UK Customer default settings4D DCP UK Customer default settings
001Unlocking the device from its mobile operator

Consult only - if DCP is sim locked or not?UNLOCKEDSchema_MK775v160GSchema_MK775v160H_en
002Identifier of the device - Alphanumeric device ID

20 alphanumeric characters, can be renamed. No spaces.MIQUEL_ROMEU_56P002 MCXCM10100FX0000P002 TRACK_GSM_MK_775
003Reading information about software and firmware versions 

Consult only - Software / Firmware versionsBOOT:1.00; BIOS:1.00; APP:1.42; GSM 7.00.003

004IMEI consultation

Consult only - Device IMEI Info354976097655628

005CCID consultation

Consult only - SIM CCID Info89441000300184682478

006IMSI consultation

Consult only - SIM IMSI Info234159534474764

007Consultation of the device status and accumulated GPRS trafficX
Consult only - Device Status InfoI0O0B00000C66M1S19D00000
000T19L008BXSN000000000000XVC1

008Activation of VoiceID message X
Enables or disables device voice ID message, that plays when answering a call2 - Only if there is a DAUP008 = 2P008 = 2
Hardware management functions




009Battery alarm adjustmentX
Set the voltage at which a low battery fault is created7 - 12.30vP009 = 7P009 = 7
010Logic input filtering timeX
The time it takes for an electrical input to be registered by the device - in seconds.1P010 = 01P010 = 01
011Logic output operation modeX
Defines the J11 logic output function. for example enabled on low battery0 - Bistable (Remote control)P011 = 0P011 = 0
012Activation time of the logic output in pulse mode X
Defines pulse time in seconds of J11 output (if set to pulse)5P012 = 01P012 = 01
013Forced logic output in remote control modeX
Changes the logic output statusof J11 if P011 is set to 00

014Definition of the events generating status transmission X3Define which fault outputs should be transmitted automatically7 - I/O+230VAC+BatteryP014 = 7P014 = 7
015Mask of enabled events transmission

Select events that if detected will be visible in the transmission of a status reportFFFFP015 = FFFFP015 = FFFF
Configuration functions of the RS-232/RS-485/RS-422 port




016Allowing AT modem or repeater UDP functionalities X
Set as 0,1 or 2 for Default, AT modem or UDP repeater functionality0 - No extra functionP016 = 0P016=  0
017Configuration of the serial port baud rate X
Set Baud rate (data rate at the expense of noise resistance) of the serial port.3 - 9600 bpsP017 = 3P017 = 3
018Configuration of the serial port (232/422/485)X
Configures the parity and number of stop bits of the serial port.0 - none - 1 bitP018 = 0P018 = 0
019Configuration of flow control of the RS-232 port X
enables or disables the hardware flow control of the RS-232 serial port0 - NoP019 = 0P019 = 0
Specific m2mLIFT functions




020m2mLIFT Client TypeX
Configures the local device communications - DTMF or Data? Changes back to CAN automatically06 (CAN?)P020 = 21P020 = 21
021m2mLIFT Parameter 1 (ID MSB)X
Specific DCP ID part 1 , in analogue/PSTN can be used as an access code0000P021 = 0000P021 = 0000
022m2mLIFT parameter 2 (ID LSB)X
Specific DCP ID part 20000P022 = 0000P022 = 0000
023m2mLIFT parameter 3 (response time)X
For CAN devices - self-test speaker and mic (set to 0 turns self test off)1P023 = 1P023 = 1
024m2mLIFT parameter 4 (voice conversation time)X
Alarm call time limit - Must be set to 0 for Memcom0P024 = 0P024 = 0
025m2mLIFT parameter 5 (voice calls forwarding)X
Auto forward to this number
P025 P025 
026m2mLIFT parameter 6 (DATA calls forwarding)X
same but for background or test
P026 P026 
027m2mLIFT parameter 7 (input controls the alarm filter)X
turn filter input on or off0000P027 = 0000P027 = 0000
028m2mLIFT parameter 8 (# of installed cars)X
max of 4 lift car / shaft0P028 = 0P028 = 0
Real time clock 




029Setting and real-time consultation of the clock 

Set on board clock: YYMMDDhhmm+zz


Phone lists 




030Phone 1 of voice whitelist X
Maintenance Alarm numberI or O prefix for incoming or outgoing onlyP030 P030 
031Phone 2 of voice whitelist X
Alarm number 1 no area code. (can be full phone number or just first digits ie 01628)
P031 P031 
032Phone 3 of voice whitelist X
Alarm number 2 no area code. (can be full phone number or just first digits ie 01628)
P032 P032 
033Phone 4 of voice whitelist X
Alarm number 3 no area code. (can be full phone number or just first digits ie 01628)
P033 P033 
034Phone 5 of voice whitelist X
Alarm number 4 no area code. (can be full phone number or just first digits ie 01628)
P034 P034 
035Phone 1 of DTFM, TMDT© data whitelist X
Data call number 1P035 = 3308084431 (CAN), 3308088484 (PSTN)P035 = 3308084431P035 3308084431
036Phone 2 of DTFM, TMDT© data whitelist X
Data call number 2
P036 = 970734187P036  970734187
037Phone 3 of DTFM, TMDT© data whitelist X
Data call number 3
P037 = 4997216483018P037  4997216483018
038Phone 1 of RS-232 data whitelist X
Used for transparent RS232 serial port
P038 P038 
039Phone 2 of RS-232 data whitelist X
Used for transparent RS232 serial port
P039 P039 
Management of phone lines 




040Activation of whitelists as filters for incoming calls X
Enable or disable whitelist filter for incoming calls.0 - NoP040 = 0P040 = 0
041Allowing speed dial X
enable dialling of parameter of whitelist number. Saves time.1 - YesP041 = 1P041 = 1
042Outgoing calls configuration/filterX
enables and disables blocking or forwarding outgoing calls1 - YesP042 = 0P042 = 0
Carrier selection




043Voice calls in TMDT© special carrier created by MKX3Enable and disable TMDT (mk software cleans up data, instead of DTMF) define voice call format0 - NoP043 = 0P043 = 0
044Carriers for SLIC transparent data calls X3Transparent mode - defines the carriers for SLIC data calls. Up to 4 back ups Analogue device00001 (UDP, TCP, TMDT, CSD, DTMF)P044 = 00001P044 = 00001
045Carriers for RS-XXX transparent data callsX3Transparent mode - defines the carriers for RS-XXX. Up to 2 back ups001 (UDP, TCP, CSD)P045 = 001P045 = 001
046Carriers for m2mLIFT reports X3Transparent mode - defines the carriers for m2mLIFT. Up to 2 back ups001 (UDP, TCP, CSD)P046 = 100P046 = 100
047Timeout for end of frame DTMF X
Defines reception timeout in 100ms, of client device in DTMF 10P047 = 00P047 = 00
CAN Configuration




048CAN bus configurationX
Define CANbus format (data rate and ID) in hexadecimal 3960A0P048 = 3960A0P048 = 3960A0
049CAN device identifierX
Defines identifier configuration for CANbus frames
P049 = 00000000P049 = 00000000
051Single sim or dual sim setting

0 or 1
P051 = 0P051 = 0
052Force Telco (Roaming)


0 - TX GPRS LockedP052 P052 
053AES Key

The key for the encryption of the VDS protocol.
P053 0000000000000000
0000000000000000		P053 = 00000000000000000000000000000000
Special telephones




054Phone 1 for GPRS context captures X3Phone no. where DCP rejects the first received call and activates the data connectionmax. 15 digitsP054 = 3308084431P054  3308084431
055Phone 2 for GPRS context captures X3Phone no. where DCP rejects the first received call and activates the data connectionmax. 15 digitsP055 P055 
056Temporary phone for configuration via CSDX
Phone no. for temporary remote configuration in CSD formatmax. 15 digitsP056 P056 
057Permanent phone for configuration via CSDX
Phone no. for permanent remote configuration in CSD formatmax. 15 digitsP057 P057 
058Destination phone for SMS messages X
Phone no. that will be sent event notifications by SMSmax. 15 digitsP058 P058 
059Phone for remote debugging

Phone no for remote debugging682161503P059 = 682161503P059 = 682161503
088Self check phone numberX2&3Freephone number that autohangs up for each country/network - test call function191P088 P088 
GPRS





060Name of the GPRS services APN
2APN of the SIM Data providerwap.vodafone.co.ukP060 = wlapn.comP060 wlapn.com
061GPRS connection user name
2APN user name of the SIM Data providerwapP061 P061 
062GPRS connection user password
2APN password of the SIM Data providerwapP062 P062 
063GPRS context mode (temporary or permanent) 
3Configure data mode - temporary data on request or permanently on1 - Temporary connection (IP report by m2mLIFT)P063=  1P063 = 1
064GPRS heartbeat period
3Time between data "heartbeat" checks - value in minutes4320 (3 days)P064 = 4320P064 = 4320
065Forced context activation / IP address consultation

Data on/off. Also consult for Device IP address if it has one.10.35.42.313

066IP or name of the A host 
3Data Server Host A (can only be used for Avire HUB)avirehub.avire-global.comP066 = avirehub.avire-global.comP066 avirehub.avire-global.com
067IP or name of the B host 
3Data Server Host B (used for various including VDS call centres)
P067 P067 
068Port for transparent UDP and TCP-Link communications

Defines the name for host IP addresses. Not required for static IP address


069Outgoing UDP Port 
3Specific program (process) ID for outgoing UDP connections6000P069 = 6000P069 = 6000 
070IP server port 
3Specific program (process) ID in server software that the data needs to be sent to.6000P070 = 6000P070 = 6000
071Directory and resources for data and remote configuration 
3Defines the HTTP directory and resource namem2mLIFT.phpP071 = /m2mLIFT.phpP071 = /m2mLIFT.php
072IP of allowed input (firewall) 

Defines the allowed firewall input IP address1.1.1.1P072 = 1.1.1.1P072 = 1.1.1.1
073Mask of input IP (firewall)

Defines the allowed firewall IP mask255.255.255.0P073 = 255.255.255.0P073 = 255.255.255.0
Audio Adjustments




074Playing recorded voice messagesX
Parameter can be used to start playing the automated message to identify the device


075Voice message recordingX
Parameter starts recording message. Guidance and location


076‘ON’ time in DTMF or TMDT© tones X
define time duration of created DTMF or TMDT tones (P020 = P100 will auto change to 100ms)2 - 80msP076 = 2P076 = 2
077‘OFF’ time in DTMF tone X
Pause between DTMF tones in 10ms starting with 0=60ms2 - 80msP077 = 2P077 = 2
078Configuration of the GSM voice codec X2GSM Voice codec selection - defines codec requested by mobile operatorAutomaticP078 =  0P078 = 0
079Adjustments of audio volume of the deviceX
Audio adjustments between different audio protocols5005P079 = 5005P079 = 5005
Adjustment of local phone line impedance




080Selection of impedance of the local phone line X
Local phone line AC impedance0 - 600 resistiveP080 = 0P080 = 0
Audio connection with digital audio modules




081Activation of audio with cabin 1 X
Not used any more


082Activation of audio with cabin 2 (in multi-cabins)X




083Activation of audio with cabin 3 (in multi-cabins)X




84Activation of audio with cabin 4 (in multi-cabins)X




Configuration Language




085Configuration language selectionX1Choose device language 1-64 - EnglishP085 = 4P085 = 4
DNS server 




086IP of the DNS server X2DNS server IP address0.0.0.0P086 = 0.0.0.0P086 = 0.0.0.0
087PBX Signalling
1Country specific PBX format4335P087 = 4335P087 = 4335
Access codes and firmware updates




050URL for file downloads 

Specify URL address for remote file downloads<type>,<file URL>

052Force phone operator selectionX
If an operator has low coverage, you can specify another by entering operator code.5 digit code

089Blocking due to SIM changeX
 Match device to SIM, will not work with another sim after setting1234567890

090PIN configuration on mobile operator’s SIM X
SIM card PIN unlock


091Super settingsX
3 digit or (4 for dual sim) multi parameter shortcut441

092PUK+PIN configuration of the MKSIMX
mkPUK of the mkSIM: 0000FFFFFFFFFFFFP092 0000FFFFFFFFFFFFP092 = 0000FFFFFFFFFFFF
093Access code configurationX
Pinxxxx access code for changing parameters1234P093 = 1234P093 = 1234
094Debugging utilities

Range of debugging features including force background test0 -P094P094 
095Device reset X
Forces a device reset. No files will be lost1234567890

096Erasing the external temporary flash memory

erase flash and resets it. Doesn’t effect parameters


097Data for remote update 





098Remote update + reset

Resets device and updates firmwareCCCC = checksum

099Default values X
Reset all parameters to default values1234567890

Auxillary Devices 




XyyX = Lift, yy = Command





Devices




100-199Cabin 1 devices

CAN device parameters 1


200-299Cabin 2 devices

CAN device parameters 2


300-399Cabin 3 devices

CAN device parameters 3


400-499Cabin 4 devices

CAN device parameters 4


500-599Temporarily not assigned





600-699Temporarily not assigned





700-799General commands for the whole installation 

Used for other CAN devices such as Panachrome / Connex / Navbox


800-999Virtual device included in the MK-0775

Special firmwares for customer - on request